Table of Contents
A 22.5 degree angle is one of the more common angles used in woodworking, so it is important to know how to cut this angle on your miter saw. There are lot of cheap miter saw available in the market, you can buy for cutting purposes. The most accurate way to cut any given angle is with a beveled miter gauge that matches the exact angle you wish to use. This guide will teach you how to cut a 22.5 degree angle on a miter saw.
As with all angles, whether it is a 20.5 or 45 degree angle, they are most easily measured by the amount of degrees (or fraction thereof) contained within the angle in question.
For most miter saws on the market today, 22.5 degrees are about as accurate as you will get without purchasing anything other than the most basic of miter saws.
Miter saws with laser guides provide an indication on where the blade will ultimately end up, however they can usually only provide a fairly accurate idea of where it is at the very moment that you trigger the laser and then release it.
The downfall to this is that while some lasers may provide decent enough feedback for beginners, it is not something that should be relied on by more experienced craftsmen.
How to cut 22.5 degree angle on a miter saw
That being said, the best way to cut a 22.5 degree angle with any miter saw (assuming that you are using one of the larger 10″ models) is to follow these steps:
Procedure of cutting 22.5 degree angle on miter saw
Step 1:
Measure the work piece and then cut it to length. Be sure that you do not cut it too short, as this will only cause problems down the line and besides, if you do cut it too short there is a good chance that you may have to undo what you did before cutting a longer piece of wood.
Step 2:
Hold the miter saw so that it is perpendicular to what you are cutting.
Step 3:
Make sure that the blade of the saw is angled properly for making a 22.5 degree cut, then lock down your measurements with either your back or side hand. Always be sure that the angle on your saw remains locked into position – otherwise, you may find yourself with a crooked cut.
Step 4:
Hold the work piece firmly in place (in your fingers or vise grip), and make sure that it is set to the appropriate depth for making this type of cut. Make sure that you are firm enough on the wood so that it does not move around while you are cutting it.
Step 5:
Finally, make your final cuts on the work piece and then remove the excess material that you created during this process. You will now be able to use them as they were meant to be used, no more guessing on angles.
Although this article is about how to cut a 22.5 degree angle on a miter saw, this knowledge is applicable to any type of miter saw.
Tips and Instructions about cutting 22.5 degree angle.
1-Always make sure that your measurements are correct
2-In general, it is a good idea to check with either a framing square or combination square before making any cuts, especially when using a miter saw.
3-Lastly and most importantly, always be sure to double and even triple check your measurements, so that you can be confident in what you’re doing and avoid costly mistakes.
You should follow these steps carefully, then you will know how to cut a 22.5 degree angle on a miter saw with no problems at all.
Conclusion
It is imperative that you carefully follow the steps outlined in this article so that you can be sure of how to cut a 22.5 degree angle on a mitre saw, because each step is equally important for ensuring accuracy and precision while performing any type of cutting process.
FAQs
1. Will this process work for cutting any angle on a miter saw?
Yes, the steps outlined in this article can be used for cutting any sort of angle on a mitre saw as long as you follow them carefully and make sure that you (a) lock down your blade at the appropriate angle and (b) make sure that you hold the wood securely in place.
2. How much material will I lose during a cut?
You will usually lose between one and two inches of material during a single cut, but this may vary depending on how deep you make your final cut and what type of blade you are using. Make sure to read the packaging on your saw or blade to know how much you should expect to lose during any given cut.
3. Will this method work for other types of saws?
Yes, you can use these steps for cutting angles on radial arm and sliding compound mitre saws as well as table saws and band saws; basically, any type of saw that has a blade can utilize these steps.
4. I am having problems with making this cut; what should I do?
The first thing that you should check is whether or not the blade of your saw is properly aligned at 22.5 degrees, as this could potentially cause a problem with your finished cuts and might even lead to injury if it is not reset to its original position.
5. Do I need to use a miter box?
No, you do not need to use a miter box when making cuts for this type of project. However, it can help you achieve more accurate cuts if you are having problems with positioning or accuracy, but it is not required for completion of the project itself.
6. How should I change the angle on my saw?
Some miter saws have a crank that can be turned to adjust the angle of your blade. However, it is usually best to use an Allen wrench in order to make changes because this ensures greater accuracy. Always make sure that you read and follow any instructions before attempting these steps with your own saw.
7. What if I’ve completed my cuts but there are some rough edges?
Rough edges may occur after you make a cut, and they should be removed carefully with a fine-grit sandpaper or a sharp blade before making any other cuts on the wood itself, this will help to ensure that the work piece is properly aligned and will help to provide a smoother surface for further cutting.